摘要：The tokamak start-up is a very important phase during the process to obtain a suitable equalizing plasma, and its governing model can be described as a set of nonlinear ordinary differential equations（ODEs）. In this paper, we first estimate the parameters in the original model and set up an accurate model to express how the variables change during the start-up phase, especially how the plasma current changes with respect to time and the loop voltage. Then, we apply the control parameterization method to obtain an approximate optimal parameters selection problem for the loop voltage design to achieve a desired plasma current target. Computational optimal control techniques such as the variational method and the costate method are employed to solve the problem, respectively. Finally, numerical simulations are performed and the results obtained via different methods are compared. Our numerical parameterization method and optimization procedure turn out to be effective.

摘要：This ranearch is focused on the, develonment of a simnle design model of the submerged catalysis/membrane filtration （catalysis/MF） system for phenol hydroxylation over TS-1 based on the material balance of the phenol under steady state and the reported kinetic studies. Based on the developed model, the theoretical phenol Conversions at steady state could be calculated using the kinetic parameters obtained from the previous batch experiments. The theoretical conversions are in good agreement with the experimental data obtained in the submerged catalysis/MF system within relative error of ±5%. The model can be used to determine the optimal experimental conditions to carry out the phenol hydroxylation over TS-1 in the submerged catalysis/MF system.

摘要：The key exchange is a fundamental building block in the cryptography. Several provable security models for the key exchange protocol are proposed. To determine the exact properties required by the protocols, a single unified security model is essential, The eCK , eCK and CK models are examined and the result is proved that the eCK＇ model is the strongest provable security model for the key exchange. The relative security strength among these models is analyzed. To support the implication or non-implication relations among these models, the formal proofs and the counter-examples are given.

摘要：This paper introduces the design and construction of global navigation satellite systems(GNSS)vulnerability simulation,verification,and mitigation *** platform contains five modules:simulation of the signal-in-space environment,simulation of the vulnerabilities in the space segment,signal quality monitoring and data processing,vulnerability assessment and validation,and integrated *** provides a set of integrated simulations of different types of interference in the GNSS signal propagation domain,including electromagnetic interference,atmospheric disturbances,multipath,and interference in the inter-satellite *** paper focuses on the design of the main system modules and testing through an experimental *** results demonstrate both the effectiveness and realism of the modules and overall platform.

摘要：To gain a deep insight into the hot drawing process of aluminum alloy sheet, simulations of cylindrical cup drawing at elevated temperatures were carried out with experimental validation. The influence of four important process parameters, namely,punch velocity, blank holder force(BHF), friction coefficient and initial forming temperature of blank on drawing characteristics(*** thickness and thickness deviation) was investigated with the help of design of experiments(DOE), analysis of variance(ANOVA) and analysis of mean(ANOM). Based on the results of ANOVA, it is shown that the blank holder force has the greatest influence on minimum thickness. The importance of punch velocity for thickness deviation is 44.35% followed by BHF of 24.88%,friction coefficient of 15.77% and initial forming temperature of blank of 14.995%. After determining the significance of each factor on forming characteristics, how the individual parameter affects characteristics was further analyzed by ANOM.

摘要：The design and synthesis of highly active non-noble metal oxide catalysts, such as transition- and rare-earth-metal oxides, have attracted significant attention because of their high efficiency and low cost and the resultant potential applications for the degradation of volatile organic compounds(VOCs). The structure-activity relationships have been well-studied and used to facilitate design of the structure and composition of highly active catalysts. Recently, non-noble metal oxides with porous structures have been used as catalysts for deep oxidation of VOCs, such as aromatic hydrocarbons, aliphatic compounds, aldehydes, and alcohols, with comparable activities to their noble metal counterparts. This review summarizes the growing literature regarding the use of porous metal oxides for the catalytic removal of VOCs, with emphasis on design of the composition and structure and typical synthetic technologies.

摘要：The traditional zinc hydro-metallurgy generates a large amount of zinc ferrite residue rich in valuable metals. The separation of iron is crucial for resource recycling of valuable metals in zinc ferrite residue. A novel selective reduction roasting？leaching process was proposed to separate zinc and iron from zinc leaching residue which contains zinc ferrite. The thermodynamic analysis was employed to determine the predominant range of Fe3O4 and ZnO during reduction roasting process of zinc ferrite. Based on the result of thermodynamic calculation, we found thatV（CO）/V（CO＋CO2） ratio is a key factor determining the phase composition in the reduction roasting product of zinc ferrite. In the range ofV（CO）/V（CO＋CO2） ratio between 2.68% and 36.18%, zinc ferrite is preferentially decomposed into Fe3O4 and ZnO. Based on thermogravimetric （TG） analysis, the optimal conditions for reduction roasting of zinc ferrite are determined as follows： temperature 700？750 °C, volume fraction of CO 6% and V（CO）/V（CO＋CO2） ratio 30%. Based on the above results, zinc leaching residue rich in zinc ferrite was roasted and the roasted product was leached by acid solution. It is found that zinc extraction rate in zinc leaching residue reaches up to 70% and iron extraction rate is only 18.4%. The result indicates that zinc and iron can be effectively separated from zinc leaching residue.

摘要：A dynamic measuring apparatus was developed to investigate the infiltration process of liquid metal into the fibrous preform. 10% （volume fraction） chopped carbon fiber preforms were infiltrated with magnesium alloy under different infiltration pressures. The threshold pressure and flow behavior of liquid metal infiltrating into the preforms were calculated and measured. The microstructure of obtained Ct4Mg composites was observed. The results indicate that the measured threshold pressure for infiltration was 0.048 MPa, which was larger than the calculated value. The infiltration rate increased with the increase of infiltration pressure, but the increase amplitude decreased gradually. The tiny pores in the composites could be eliminated by increasing the infiltration pressure. When the infiltration pressure rose to 0.6 MPa, high quality C1/Mg composite was obtained.

摘要：The ultra-low specific speed centrifugal blower is widely used in energy industries due to its features such as low flow rate,high pressure and low manufacturing cost. However,the width-to-diameter ratio of the above blower becomes relatively small to satisfy the needed operation condition and its performances are considerably degraded as a result of relatively high leakage,disc friction and passage friction loss consequently. The purpose of this paper is to improve its performance through the optimization design of the blade’s profile properly. Based on artificial neural networks (ANN) and hierarchical fair competition genetic algorithms with dynamic niche (HFCDN-GAs),the optimization design approach is established. By conjoining Bezier parameterization and FINE/TURBO solver,the optimized blade is designed by adjusting the profile gradually. An industrial ultra-low specific speed centrifugal blower with parallel hub and shroud has been selected as a reference case for optimization design. The performance investigations of the centrifugal blowers with different types of blades are conducted. The conclusions of the performance improvement of the optimized blade provide positive evidences in the application of the optimization design of the above blower blade.

摘要：Acidic oligosaccharide sugar chain （AOSC）, a D-mannuronic acid oligosaccharide, derived from brownalgaepolysaccharide, has been completed Phase I clinical trial in china as an anti-Alzheimer＇s Disease （AD） drug candidate. The identification of AOSC-binding protein（s） in neurons is very important for understanding its action mechanism. To determine the binding protein（s） of AOSC in neurons mediating its anti-AD activities, confocal microscopy, affinity chromatography, and liquid chromatography-tandem mass spectrometry （LC-MS/MS） analysis were used. Confocal microscopy analysis shows that AOSC binds to SH-SY5Y cells in concentration-, time-, and temperature-dependent fashions. The AOSC binding proteins were purified by affinity chromatography and identified by LC-MS/MS analysis. The results showed that there are 349 proteins binding AOSC, including clathrin, adaptor protein-2 （AP-2） and amyloid precursor protein （APP）. These results suggest that the binding/entrance of AOSC to neurons is probably responsible for anti-AD activities.