摘要：To achieve better cycling performance and vibration comfort of mountain bicycle, the optimization of frame structural parameters and rear suspension scale parameters is investigated based on ***, the quadratic sum of rider lower limb muscles stresses is presented as the evaluation criterion of muscle *** taking the criterion as the objective function, the relative positions of three pivot points of frame are optimized to ensure that the frame structural parameters match the stature o...

摘要：Anterior cruciate ligament （ACL） injuries are common in soccer. Understanding ACL loading mechanisms and risk factors for ACL injury is critical for designing effective prevention programs. The purpose of this review is to summarize the relevant literature on ACL loading mechanisms, ACL injury risk factors, and current ACL injury prevention programs for soccer players. Literature has shown that tibial anterior translation due to shear force at the proximal end of tibia is the primary ACL loading mechanism. No evidence has been found showing that knee valgus moment is the primary ACL loading mechanism. ACL loading mechanisms are largely ignored in previous studies on risk factors for ACL injury. Identified risk factors have little connections to ACL loading mechanisms. The results of studies on ACL injury prevention programs for soccer players are inconsistent. Current ACL injury prevention programs for soccer players are clinically ineffective due to low compliance. Future studies are urgently needed to identify risk factors for ACL injury in soccer that are connected to ACL loading mechanisms and have cause-and-effect relationships with injury rate, and to develop new prevention programs to improve compliance.

摘要：Objective： In pedicle screw fixation, the heads of monoaxial screws need to be directed in the same straight line to accommodate the rod placement by backing out during operation, which decreases the insertional torque and internal fixation strength. While polyaxial screws facilitate the assembly of the connecting rod, but its ball-in-cup locking mechanism reduces the static compressive bending yield strength as compared with monoaxial screws. Our study aimed to assess the mechanical performance of a modified pedicle screw. Methods： In this study, the tail of the screw body of the modified pedicle screw was designed to be a cylindershaped structure that well matched the inner wall of the screw head and the screw head only rotated around the cyclinder. Monoaxial screws, modified screws and polyaxial screws were respectively assembled into 3 groups ofvertebrectomy models simulated by ultra high molecular weight polyethylene （UHMWPE） blocks. This model was developed according to a standard for destructive mechanical testing published by the American Society for Testing Materials （ASTM F1717-04）. Each screw design had 6 subgroups, including 3 for static tension, load compression and torsion tests, and the rest for dynamic compression tests. In dynamic tests, the cyclic loads were 25%, 50%, and 75% of the compressive bending ultimate loads respectively. Yield load, yield ultimate load, yield stiffness, torsional stiffness, cycles to failure and modes of failure for the 3 types of screws were recorded. The results of modified screws were compared with those ofmonoaxial and polyaxial screws. Results： In static tests, results of bending stiffness, yield load, yield torque and torsional stiffness indicated no significant differences between the modified and monoaxial screws （P〉0.05）, but both differed significantly from those ofpolyaxial screws （P〈0.05）. In dynamic compression tests, both modified and monoaxial screws showed failures that occurred at the insertion point

摘要：Objective： To study biomechanical changes of newly formed bones 24 weeks after repairing large defects of long bones of goats using heterogeneous deproteinated bone （DPB） prepared by modified methods as an engineering scaffold. Methods： According to a fully randomized design, 18 goats were evenly divided into three groups： normal bone control group （Group A）, autologous bone group （Group B） and experimental group （Group C）. Each goat in Groups B and C were subjected to the periosteum and bone defect at middle-lower part of the right tibia （20% of the whole tibia in length）, followed by autologous bone or DPB plus autolognus MSCs ＋ rhBMP2 implantation, respectively and semi- ring slot fixation; while goats in Group A did not perform osteotomy. At 24 weeks after surgery, biomechanical tests were carried out on the tibias. Results： At 24 weeks after surgery, the results of anticompression test on tibias in three groups were recorded by a functional recorder presented as linear pressure-deformation curve. The shapes of the curves and their change tendency were similar among three groups. The ultimate pressure values were 10.74 MPa±1.23 MPa, 10. 11 MPa±1.35 MPa and 10.22 MPa±1.32 MPa and fracture compression rates were 26.82%±0.87%, 27.17%±0.75% and 28.22%±1.12% in Groups A, B and C, respectively. Comparisons of anti-compression ultimate pressures and fracture compression rates among three groups demonstrated no significant difference （PAB=0.415, PBC=0.494）. Three-point antibend test on tibias was recorded as load-deformation curves, and the shapes of the curves and their change tendency were similar among three groups. The ultimate pressure values of the anti-bend test were 481.52 N±12.45 N, 478.34 N±14.68 N and 475.62 N±13.41 N and the fracture bend rates were 2.62 mm±0.12 mm, 2.61 mm±0.15 mm and 2.81 mm±0.13 mm in Groups A, B and C, respectively. There was no significant difference between groups （PAB=0.7, PBc=0.448）. The ultimate anti-torsion torque values were 6.5

摘要：In order to help companies to improve their competetiveness, it is important to develop new design methodologies. In this framework, a Functional And Robust Design (FARD) methodology dedicated to routine design of “highly productive” modular product ranges is proposed including principles of functional analysis, Design For Assembly (DFA), and techniques of modelling and simulation for ergonomics consideration. This paper focuses on the application of this original method applied to mechanical vibration and ergonomics problems of a scraper. Including biomechanical aspect in the design methodology, it is possible to identify the impact of a vibration tool on its users using numerical models of the tool coupled to a finite element model of the human hand. This method can proactively warn very early, in the design process, the risks of causing musculoskeletal disorders and facilitate an optimization of the mechanical tool. This study is a first step in a context of human-centered design.