摘要：The plasma-MIG welding torch was developed.5A06 aluminum alloys with V-grooves were welded in a single pass in the plasma-MIG welding process and the joints were examined by X-ray diffractometry analysis and mechanical *** orthogonal experimental design was used to study the influence of plasma-MIG welding parameters on the aluminum weld *** mixed orthogonal matrix L16(4 4×2 3) and analysis of variance (ANOVA)technique were employed to optimize the welding *** experimental results indicate that the effect of plasma gas flow rate is dominant,the secondary factors are MIG welding voltage,welding speed,wire feed rate and plasma current in *** experiments were conducted under optimum conditions and there was almost no porosity in the welded joints,thus good mechanical performance joints were obtained.

摘要：The effect of porosity on compressive,bending,and tensile properties of the porous tantalum scaffolds fabricated by electron beam powder bed fusion(EB-PBF)was *** porous tantalum scaffolds with porosity from 69%to 77.8%were obtained by varying the designed porosity and adjusting the processing *** is found that the pores and unfused powder decrease with the increase of deposited energy *** decrease of porosity leads to an improvement in mechanical *** relevancy between compressive/bending/tensile yield strength and relative density can be described appropriately by exponential model,while the relationship between elastic modulus and relative density is in good agreement with the Gibson-Ashby *** the porous tantalum scaffolds exhibit good ductility in compressive,bending and tensile *** fragmentation of struts is observed during the compression process,but cracks are formed on the strut surface after 90°bending,mainly due to the high sensibility to defects caused by the oxide.

摘要：Controlling process parameters of lost foam casting （LFC） enables this process to produce defect-free complex shape castings. An experimental investigation on lost foam casting of an A1-Si-Cu cast alloy was carried out. The effects of pouting temperature, slurry viscosity, vibration time and sand size on surface finish, shrinkage porosity and eutectic silicon spacing of thin-wall casting were investigated. A full two-level factorial design of experimental technique was used to identify the significant manufacturing factors affecting the properties of casting. Pouring temperature was found as the most significant factor affecting A1-Si-Cu lost foam casting quality. It was shown that flask vibration time interacted with pouring temperature influenced euteetic silicon spacing and porosity percentage significantly. The results also revealed that the surface quality of the samples cast in fine sand moulds at higher pouring temperatures was almost unchanged, while those cast in coarse sand moulds possessed lower surface qualities. Furthermore, variation in slurry viscosity showed no significant effect on the evaluated properties compared to other parameters.

摘要：Miniature cylindrical metal powder sintered wick heat pipe （sintered heat pipe） is an ideal component with super-high thermal efficiency for high heat flux electronics cooling. The sintering process for sintered wick is important for its quality. The sintering process was optimally designed based on the equation of the heat transfer limit of sintered heat pipe. Four-step sintering process was proposed to fabricate sintered wick. The sintering parameters including sintering temperature, sintering time, sintering atmosphere and sintering position were discussed. The experimental results showed that the proper sintering temperature was 950 ℃ for Cu powder of 159μm and 900 ℃ for Cu powders of 81 and 38 μm, respectively, while the wick thickness was 0.45 mm and sintering time was 3 h. The optimized sintering time was 3 h for 0.45 and 0.6 mm wick thickness and 1 h for 0.75 mm wick thickness, respectively, when copper powder diameter was 159μm and sintering temperature was 950 ℃. Redox reduction reaction between H2 and CuO during sintering could produce segmentation cracks in Cu powders as a second structure. Sintering at vertical position can effectively avoid the generation of gap between wick and the inner wall of pipe.

摘要：The aim of this work was to develop a Ti6Al4V/20CoCrMo−highly porous Ti6Al4V bilayer for biomedical *** powder metallurgy technique,with semi-solid state sintering as consolidation step,was employed to fabricate samples with a compact top layer and a porous bottom layer to better mimic natural *** densification behavior of the bilayer specimen was studied by dilatometry and the resulting microstructure was observed by scan electron microscopy(SEM)and computed microtomography(CMT),while the mechanical properties and corrosion resistance were evaluated by compression and potentiodynamic tests,*** results indicate that bilayer samples without cracks were obtained at the interface which has no negative impact on the *** values of the highly porous layer were in the lower range of those of human *** compression behavior is dictated by the highly porous Ti6Al4V ***,the corrosion resistance of Ti6Al4V/20CoCrMo is better than that of Ti6Al4V,which improves the performance of the bilayer *** work provides an insight into the important aspects of a bilayer fabrication by powder metallurgy and properties of Ti6Al4V/20CoCrMo−highly porous Ti6Al4V structure,which can potentially benefit the production of customized implants with improved wear performance and increased in vivo lifetime.

摘要：Both porosity ( φ ) and permeability ( k ) of the weathered elution deposited rare earth ores are basic hydrodynamic parameters for RE leaching. The relationship between k and φ of two typical rare earth ores of South China in the packed bed was investigated by measuring the flow ( Q ) under various leaching pressure difference (Δ p ). The experimental results show that the relationship between k and φ is unique, moreover the relationship between Q and Δ p is in accord with the Darcy’s law. The effects of the type of ores, the leaching reagents and its concentration, the granule ore size on the leaching permeability have also been investigated. It is demonstrated that k H (for heavy RE ore, k H=35.98?mm 2)> k M H (for middle heavy RE ore, k M H =28.50?mm 2), whereas k (NH 4NO 3)> k (NH 4Cl)> k [(NH 4) 2SO 4], and the k value increases with increasing leaching reagents concentration and granule ore size( k 0.60～0.75?mm =99.96?mm 2, k 0.125～0.60?mm =11.83?mm 2, k 0.074～0.125?mm =0.84?mm 2). [

摘要：Wind force coefficients for designing porous canopy roofs have been investigated based on a series of wind tunnel experiments. Gable, troughed and mono-sloped roofs were tested. The roof models were made of 0.5 mm thick perforated duralumin plates, the porosity of which was changed from 0 to about 0.4. Overall aerodynamic forces and moments acting on the roof model were measured in a turbulent boundary layer with a six-component force balance for various wind directions. The results indicate that the wind loads on canopy roofs generally decrease with an increase in porosity of the roof. Assuming that the roof is rigid and supported by the four corner columns with no walls, the axial forces induced in the columns are regarded as the most important load effect for discussing the design wind loads. Two loading patterns causing the maximum tension and compression in the columns are considered. Based on a combination of the lift and moment coefficients, the design wind force coefficients on the windward and leeward halves of the roof are presented for the two loading patterns as a function of the roof pitch and porosity. The effect of porosity is taken into account as a reduction factor of the wind loads.

摘要：A large number of experiments have been done for analyzing the two important indicators -compressive strength and flexural strength, which affect computer numerical control （CNC） engraving material physical properties. Using Matlab for simulation experiment, the processing quality of different intensity brick materials is analyzed by the theory of fracture toughness. The result show that porosity is an important factor for engraving, and the research also provide a reference for further study which can improve the quality of brick carving.