摘要：Mg-Al alloys have excellent strength and ductility but relatively low thermal conductivity due to Al *** accurate prediction of thermal conductivity is a prerequisite for designing Mg-Al alloys with high thermal ***,databases for predicting temperature-and composition-dependent thermal conductivities must be *** this study,Mg-Al-La alloys with different contents of Al2La,Al3La,and Al11La3phases and solid solubility of Al in the α-Mg phase were *** influence of the second phase(s) and Al solid solubility on thermal conductivity was *** results revealed a second phase transformation from Al_(2)La to Al_(3)La and further to Al_(11)La_(3)with the increasing Al content at a constant La *** degree of the negative effect of the second phase(s) on thermal diffusivity followed the sequence of Al2La>Al3La>Al_(11)La_(3).Compared with the second phase,an increase in the solid solubility of Al in α-Mg remarkably reduced the thermal *** the basis of the experimental data,a database of the reciprocal thermal diffusivity of the Mg-Al-La system was established by calculation of the phase diagram (CALPHAD)*** a standard error of±1.2 W/(m·K),the predicted results were in good agreement with the experimental *** established database can be used to design Mg-Al alloys with high thermal conductivity and provide valuable guidance for expanding their application prospects.

摘要：Ce element was introduced to modify Al−2%Fe(mass fraction)binary *** microstructures,crystallization behavior,electrical/thermal conductivities and mechanical properties of these alloys were systematically *** results indicated that the appropriate Ce addition decreased the recalescence temperature and growth temperature of Al−Fe eutectic structure,improved the morphology and distribution of Fe-containing phase,and simultaneously increased the conductivity and mechanical *** annealed treatment improved the thermal conductivity of these alloys due to the decreasing concentration of point *** process further broke up the coarser Fe-containing phases into finer particles and made the secondary phases uniformly distributed in theα(Al)*** subsequent annealing treatment and rolling deformation,the thermal conductivity,ultimate tensile strength and hardness of the Al−2%Fe−0.3%Ce(mass fraction)alloy reached 226 W/(m·K),(182±1.4)MPa and HBW(49.5±1.7),respectively.

摘要：The thermal conduction of suspended few-layer hexagonal boron nitride （h-BN） sheets was experimentally investigated using a noncontact micro-Raman spectroscopy method. The first-order temperature coefficients for monolayer （1L）, bilayer （2L） and nine-layer （9L） h-BN sheets were measured to be -（3.41 ± 0.12）× 10-2, -（3.15 ± 0.14） × 10-2 and -（3.78 ±0.16）× 10-2 cm-1.K-1, respectively. The room-temperature thermal conductivity of few-layer h-BN sheets was found to be in the range from 227 to 280 W.m-1-K-1, which is comparable to that of bulk h-BN, indicating their potential use as important components to solve heat dissipation problems in thermal management configurations.

摘要：There is a lack of thermophysical data of heat transfer oil and nano-oil in the high temperature range of 50-300 ℃ for designing and developing heat transfer oil furnace and its heating systems. In the present study, the thermal conductivity values of heat transfer oil and TiO2 nano-oil in the above high temperature range were measured by a newly developed high-temperature thermal conductivity meter. Based on the principle of least square method, the thermal conductivity values obtained from experiments were fitted separately, and the correlation between thermal conductivity and temperature of heat transfer oil and TiO2 nano-oil was obtained. The results show that the thermal conductivity and the increased percentage of thermal conductivity of TiO2 nano-oil are proportional to the increase of particle size and mass fraction of nanoparticles, but thermal conductivity is in reverse proportion to the increase of temperature and the increased percentage of thermal conductivity is less affected by temperature.

摘要：Mg-Zn-Ca-Mn series alloys are developed as promising candidates of 5G communication devices with excellent thermal conductivities,great ductility,and acceptable *** present paper,Mg-x Zn-0.4Ca-0.2Mn(x=2wt%,4wt%,6wt%)alloys were prepared by a near-solidus extrusion and the effect of Zn content on mechanical and thermal properties were *** results showed that the addition of minor Ca led to the formation of Ca_(2)Mg_(6)Zn_(3) eutectic phase at grain boundaries.A type of bimodal microstructure occurred in the as-extruded alloys,where elongated coarse deformed grains were embedded in refined recrystallized grains ***,both yield strength and ductility of the alloys were significantly enhanced after extrusion due to the great grain ***,higher Zn content led to the increment in yield strength and a slight reduction in elongation due to the larger fractions of second phase *** room temperature thermal conductivity of as-extruded alloys was also improved compared with that of as-cast *** increment of Zn content decreased the thermal conductivity of both as-cast and as-extruded alloys,which was due to the increased second phase fraction and solution atoms in the matrix,that hindering the motion of *** as-extruded Mg-2Zn-0.4Ca-0.2Mn(wt%)alloy exhibited the highest elongation of 27.7% and thermal conductivity of 139.2 W/(m·K),combined with an acceptable ultimate tensile strength of 244.0 *** present paper provides scientific guidance for the preparation of lightweight materials with high ductility and high thermal conductivity.

摘要：Classical molecular dynamics(MD)simulations ae performed to investigate the effects of mechanical strain on the thermal conductivity of single-layer black phosphorus(SLBP)nanoribbons along different directions at room *** results show that the tensile strain afects the thermal conductivity of nanoribbons by changing thephonon density of state(DOS)and mean free path(M FP).The thermal conductivity shows a sharp enhancement with the tensile strain applied along the armchai diection,while it increases slowly with the strain applied along the zigzag *** phenomenon cm be mainly explained by effects of the phonon DOS and *** increasing strain along the armchai direction weakens DOS and strengthens MFP ***,when it comes to the increasing strain along the zigzag deection'DOS enliances significantly while MFP decreases *** findings explore the relationship between the tensile strain and the thermal conductivity reasonably and can provide a reliable method to estimate the MFP of black phosphorus.

摘要：The A_(2)B_(2)O_(7)-type rare earth zirconate compounds have been considered as promising candidates for thermal barrier coating(TBC) materials because of their low sintering rate,improved phase stability,and reduced thermal conductivity in contrast with the currently used yttria-partially stabilized zirconia (YSZ) in high operating temperature *** review summarizes the recent progress on rare earth zirconates for TBCs that insulate high-temperature gas from hot-section components in gas *** on the first principles,molecular dynamics,and new data-driven calculation approaches,doping and high-entropy strategies have now been adopted in advanced TBC materials *** this paper,the solid-state heat transfer mechanism of TBCs is explained from two aspects,including heat conduction over the full operating temperature range and thermal radiation at medium and high *** paper also provides new insights into design considerations of adaptive TBC materials,and the challenges and potential breakthroughs are further highlighted for extreme environmental *** for improving thermophysical performance are proposed in two approaches:defect engineering and material compositing.

摘要：层状无机材料的弱层间耦合和大面积表面为构建低导热性无机固体材料提供了基本框架.合成具有足够散射和非谐波性的稳定层状材料,从而降低热导率,仍是一项挑战.本文在层状无机FeOCl材料体系中,通过一步氧化还原反应成功获得了一种结构稳定的富含Fe^(2+)的层状材料,实现了表面和界面的同步改性,并实现了超低的热导率.具体而言,系统的X射线吸收精细结构(XAFS)分析和电子能量损失光谱(EELS)分析表明,碱金属原子的层间插层和表面缺陷的引入诱导了大量Fe^(2+)的存在,从而增强了其非谐波性和声子散射.此外,声子态密度(PDOS)分布也提供了确凿的证据,证明了散射概率的提高和声子模式整体的软化.所制得的层状无机材料Fe(III)_(1−n)Fe(II)_(n)O_(1−x)Cl[K^(+)]_(m)不仅结构稳定,而且在298 K时的热导率比原始FeOCl降低了近60%,低至0.29 W m^(−1) K^(−1),这在层状无机材料中是极低的.这项研究为低导热层状材料的设计提供了新的视角.

摘要：The thermal expansion coefficient(TEC)and thermal conductivity(k)of thermal fillers are key factors for designing thermal management and thermal protection composite *** to its unique advantages,hexagonal boron nitride(h-BN)is one of the most commonly used thermal ***,its TEC and k values are still unclear due to the inconsistency of characterization techniques and sample *** this work,these disputes were addressed using the quasi-harmonic approximation(QHA)method and phonon Boltzmann transport equation(BTE)theory based on the density functional theory(DFT),*** accuracy of our calculated TEC and k values was confirmed by previously reported experimental results,and the underlying physical principles were analyzed from the phonon *** TEC results show that the h-BN has small in-plane negative value and large cross-plane positive value,which are-2.4×10^(-6) and 36.4×10^(-6) K^(-1) at 300 K,*** the anisotropic TEC is mainly determined by the anisotropic isothermal bulk modulus and the low-frequency out-of-plane longitudinal phonon *** found that the convergence of cutoff radius and q-grid size have significant effect on the accuracy of k of *** results show that the in-plane k is much higher than the cross-plane k,and the values at 300 K are 286.6 and 2.7 W m^(-1) K^(-1),*** anisotropic phonon group velocity arising from the vibration behaviors of acoustic phonon modes should be primarily responsible for the anisotropic *** calculated TEC and k values will provide important references for the design of h-BN composite materials.

摘要：Ni/Ti multilayers, which can be used for neutron monochromators, are designed, fabricated and measured. Firstly, their reflectivities are simulated based on the Nevot-Croce model. Reflectivities of two Ni/Ti multilayer mirrors with periods d = 10.3 nm （M1） and d = 7.8 nm （M2） are calculated. In the calculation, the reflectivity of the Ni/Ti multilayer is taken as a function of the gazing angle with different roughness factors δ =1.0 nm and = 1.5 nm. Secondly, these two multilayers are fabricated by the direct current magnetron sputtering technology. Thirdly their structures are characterized by small-angle x-ray diffraction. The roughness factors are fitted to be 0.68 nm and 1.16nm for M1 and M2, respectively. Finally their reflective performances are measured on the V14 neutron beam line at the Berlin Neutron Scattering Centre （BENSC）, Germany. The experimental data show that the grazing angle of the reflected neutron intensity peak increases, but the reflected neutron intensity decreases, with the decreasing periods of the multilayers.