摘要：相场法可以自动捕捉裂纹的萌生和演化,因此在模拟复合材料的复杂失效行为时具有明显优势。为区分纤维增强复合材料(Fiber-reinforced composites,FRC)中存在的不同断裂模式,采用双相场断裂模型来分别表征基体和纤维的损伤演化。同时采用相场变量作为误差指标,在各向异性的双相场模型中引入了基于四叉树分解的网格自适应细化策略。设计并开发了相应的Matlab程序,研究了单向及变刚度纤维增强复合材料单层板在拉伸位移载荷下的断裂行为。计算结果表明:采用基于自适应算法的各向异性双相场模型所得到的数值计算结果与试验结果吻合良好;自适应双相场模型能在保证较高计算精度的同时,配合序参量的演化准确地在裂纹路径上进行网格自动加密,简化网格前处理过程,减少网格数量,降低计算成本,提高计算效率。

摘要：This paper analyzes the effects of nanoporous surface on heat transfer temperaments of assorted thermal conductingmaterials. A phenomenal proposal of wielding the surface roughness to ameliorate the heat transfer ratehas been discovered. The maximum increase of heat transfer rate procured by nanoporous layers is 133.3% higherthan the polished bare metals of surface roughness 0.2μm. This plays an imperative role in designing compact refrigerationsystems, chemical and thermal power plants. Experimental results picture a formidable upswing of58.3% heat transfer in chemically etched metals of surface roughness 3 μm, 133.3% in nanoporous surface of porosity75-95 nm formed by electrochemical anodization, and porosity of 40-50 nm formed by spray pyrolysis increasesthe heat transfer by 130%. Effects of porosity, flow velocity and scaling on the energy transfer are alsoscrutinized. This paper also analyzes the multifarious modes of nanoporous fabrication, to contrive both prodigiousand provident system.

摘要：Emissive probes are the tools for the direct deter- mination of the plasma potential ~PL and they deliver a more reliable measure of φPL compared to the indi- rect measurements with cold Langmuir probes. The emissive probe works on the principle of compensating the well-known asymmetry of the I-V characteristic of a single cold Langmuir probe by an electron emission current from the probe into the plasma. In an ideal case, the saturated value of floating potential V（А,em） of a highly emissive probe should equal the plasma potential. A conventional emissive probe usu- ally consists of a loop of tungsten wire heated by an electric current passing through it. These conven- tional emissive probes containing an electric current- heated metal wire loop suffer a huge drawback when it comes to their lifetime. The metal wire used in these probes evaporates and subsequently breaks when heated with high current, leading to frequent replacements of these wires. When used in ultra high vacuum （UHV） plasma systems, frequent replacement of these wires requires frequent vacuum breaks in the plasma systems. In many plasma systems espe- cially in magnetized toroidal hot plasmas like toka- maks, where determination of the electric fields leads to a great deal of useful information, frequent breaking of the vacuum is impossible for changing the filament of the emissive probes. Hence, along with the other drawbacks of the conventional emissive probes such as limited emission current, bending in a magnetic field makes their use impractical in these plasma systems. The most suitable alternative is the emissive probes heated by a focused infra-red laser. Due to them having several advantages over the conventional emis- sive probes, laser heated emissive probes （LHEPs） are found to have more and more uses in plasma systems. The advantages of the LHEP are： longer lifetime （no filament breaking issues）, attainment of higher tem- perature without melting or evaporation and thus higher emissivi

摘要：Many research issues have been raised in Application Layer Multicasting(ALM),such as group management,security,integrity of data,link stress,link stretch,load balancing,fault tolerance and scalability,because of the shifting of the multicast protocol from the IP layer to the application *** address these issues many protocols have evolved by changing their topology *** this paper,the POSET protocol stack is proposed,which consists of three layers,such as communication control,POSET cube,and content *** novelty of this paper is the lattice-based data distribution with POSET cube *** results have been compared with the existing NICE and Narada *** experimental results show that the proposed POSET protocol improves throughput between 7.14%and 40%and decreases the delay between 7.69%and 25%,compared to the existing NICE protocol.

摘要：A novel method for developing a reliable data driven soft sensor to improve the prediction accuracy of sulfur content in hydrodesulfurization(HDS) process was proposed. Therefore, an integrated approach using support vector regression(SVR) based on wavelet transform(WT) and principal component analysis(PCA) was used. Experimental data from the HDS setup were employed to validate the proposed model. The results reveal that the integrated WT-PCA with SVR model was able to increase the prediction accuracy of SVR model. Implementation of the proposed model delivers the best satisfactory predicting performance(EAARE=0.058 and R2=0.97) in comparison with SVR. The obtained results indicate that the proposed model is more reliable and more precise than the multiple linear regression(MLR), SVR and PCA-SVR.

摘要：Finding an optimal trajectory from an initial point to a final point through closely packed obstacles, and controlling a Hilare robot through this trajectory, are challenging tasks. To serve this purpose, path planners and trajectory-tracking controllers are usually included in a control loop. This paper highlights the implementation of a trajectory-tracking controller on a stepper motor-driven Hilare robot, with a trajectory that is described as a set of waypoints. The controller was designed to handle discrete waypoints with directional discontinuity and to consider different constraints on the actuator velocity. The control parameters were tuned with the help of multi-objective particle swarm optimization to minimize the average cross-track error and average linear velocity error of the mobile robot when tracking a predefined trajectory. Experiments were conducted to control the mobile robot from a start position to a destination position along a trajectory described by the waypoints. Experimental results for tracking the trajectory generated by a path planner and the trajectory specified by a user are also demonstrated. Experiments conducted on the mobile robot validate the effectiveness of the proposed strategy for tracking different types of trajectories.

摘要：Technology development and continuous down scaling in CMOS fabrication makes Mixed Signal Integrated Circuits (MSIC) more vulnerable to process variation. This paper presents a well defined novel design methodology for process variability aware design by incorporating the major challenge of statistical circuit performance relating the device and circuit level variation in an accurate and efficient manner to improve the reliability, robustness and stability of the circuit. The device sensitive parameters are identified and accurately quantified by continuous realistic assessments using statistical methods. The modularity of the methodology can be validated by the output performance obtained from the gain and phase response of OTA which is highly stable when subjected to worst case process variation scenario. In the proposed optimization, the circuit is strengthened by fixing the optimum aspect ratio without adding any additional compensation devices complicating the circuit resulting in low power consumption of only 0.116 mW in standard CMOS 0.18 μm technology with 1.8 V power supply.

摘要：The main research objective in wireless sensor networks (WSN) domain is to develop algorithms and protocols to ensure minimal energy consumption with maximum network lifetime. In this paper, we propose a novel design for energy harvesting sensor node and cross-layered MAC protocol using three adjacent layers (Physical, MAC and Network) to economize energy for WSN. The basic idea behind our protocol is to re-energize the neighboring nodes using the radio frequency (RF) energy transmitted by the active nodes. This can be achieved by designing new energy harvesting sensor node and redesigning the MAC protocol. The results show that the proposed cross layer CL_EHSN improves the life time of the WSN by 40%.

摘要：The effects of the cutting parameters （cutting speed, feed rate and depth of cut） on the surface roughness in machining the Nimonic C-263 alloy were investigated. The experiments were conducted using Taguchi＇s experimental design. The effect of cutting parameters on surface roughness was evaluated and the optimum cutting conditions for minimizing the surface roughness were determined. A second order model was established between the cutting parameters and surface roughness, using the response surface methodology. The experimental results revealed that among the parameters considered, the feed rate is the most significant which influences the surface roughness, followed by the cutting speed. The predicted values and measured values are fairly close, which indicates that the developed model can be effectively used to predict the surface roughness in machining the Nimonic C-263 alloy. The predicted values are validated using the additive law.

摘要：In today’s digital era, developing digital circuits is bounded by the research towards investigating various nano devices. This paper provides the design of compact Baugh-Wooley multiplier using reversible logic. Even though various researches have been done for designing reversible multiplier, this work is the first in the literature to use Baugh-Wooley algorithm using reversible logic. In this work, a new 5 × 5 reversible multiplier cell is proposed which will be useful in designing Baugh-Wooley multiplier. The proposed single multiplier cell is able to perform addition of a 1 × 1 product with the sum and carry from the previous cell. This reversible multiplier cell is useful in building up regularity in the array multipliers. The Toffoli gate synthesis of the proposed reversible multiplier cell is also given.