摘要：For tunnels being excavated through multiple knowledge of the aquifers’hydraulic head becomes essential for determining groundwater inflow into the tunnel and analyzing its stability,specifically using multilevel monitoring *** the multi-aquifer alluvial section of the Glas tunnel(Iran),since the hydraulic head calculations were based on the data obtained from single-piezometer boreholes,the excavation risk was assessed to be at high level and the tunnel seemed to be unstable,thus an incorrect conclusion was derived from the misleading *** take cost mitigation measures into account,it was necessary to calculate the hydraulic head at tunnel level *** installing nested and clustered wells the mean hydraulic head was measured to be 70 m,significantly different from the 90 m previously determined by *** the updated value,the groundwater inflow and bulkhead load,formerly calculated as 0.65 m^(3)/s and 9.5 bars,were determined to be 0.49 m^(3)/s and 7.5 bars,respectively.

摘要：The buckling resisting brace(BRB)is an efficient system against lateral loads that enjoy high seismic energy absorption *** desirable behavior of BRBs has been confirmed,the stiffness of the system is not desirable that it can be compensated by changing the configuration of BRB *** so doing,the configuration in the form of double K(DK)is investigated to achieve more favorable ***,the required mathematical formulas were proposed to design the *** of DK system with other conventional BRB showed that the DK system has a better structural performance and is more economical(due to needing less core area)than other conventional *** results indicated that the DK system increases the lateral ultimate strength,lateral nonlinear stiffness,and energy ***,the DK configuration reduces the axial forces created in columns in the nonlinear *** material demand,created forces in the main frame,and also increasing of nonlinear stiffens by DK improve the structure’s safety.

摘要：Rockburst prediction is of vital significance to the design and construction of underground hard rock mines.A rockburst database consisting of 102 case histories,i.e.,1998−2011 period data from 14 hard rock mines was examined for rockburst prediction in burst-prone mines by three tree-based ensemble *** dataset was examined with six widely accepted indices which are:the maximum tangential stress around the excavation boundary(MTS),uniaxial compressive strength(UCS)and uniaxial tensile strength(UTS)of the intact rock,stress concentration factor(SCF),rock brittleness index(BI),and strain energy storage index(EEI).Two boosting(AdaBoost.M1,SAMME)and bagging algorithms with classification trees as baseline classifier on ability to learn rockburst were *** available dataset was randomly divided into training set(2/3 of whole datasets)and testing set(the remaining datasets).Repeated 10-fold cross validation(CV)was applied as the validation method for tuning the *** margin analysis and the variable relative importance were employed to analyze some characteristics of the *** to 10-fold CV,the accuracy analysis of rockburst dataset demonstrated that the best prediction method for the potential of rockburst is bagging when compared to AdaBoost.M1,SAMME algorithms and empirical criteria methods.

摘要：The design and performance evaluation of a sustained load creep testing machine was undertaken in this research. The design was motivated by the need to make locally available, a cost effective, technically efficient, and easily operated creep testing facility;for creep behaviour studies of materials. Design drawings and purchase of materials and components for the design were undertaken after thorough evaluation of the following design and materials selection criteria: design principle and theory, local availability of raw materials and components required for the design, material properties, cost of materials and design, ease of utilization and maintenance, and basis of testing and data capture. The machine casing and frame, heating chamber (consisting of the furnace and a dual specimen mounting stage), load lever and hanger system, and the electro-technical components;were fabricated and coupled following the produced design specifications. The machine was tested and its performance was assessed using its heating efficiency, repeatability and reproducibity of experimental test results, maintainability and cost-effectiveness as criteria. It was observed from repeat tests that the machine has the capacity of generating reliable data for computing creep strain-time results. The efficiency and temperature regulating capacity of the heating unit of the machine were also observed to be very satisfactory. The cost of the design was about 112,000 Naira ($700.00) which is cheaper in comparison to similar commercial creep testing machines from abroad. The machine was also found not to pose maintenance or repairs challenges.

摘要：High level of industrialization of northern regions of Russia cause significant pollution problems in the soil. The new approach based on fuzzy modeling for reception and processing of the geocryological information is offered. The technique and methodology of presentation of variables in a logic and linguistic way in a combination to elements of the experimental planning theory is developed. Comparison of the calculated data on model has shown its high adequacy of the experimental data of the various authors. The forecast of geoecological processes in cryolitozone on the basis of the described method will allow increasing reliability of the accepted design decisions.

摘要：Unexpected, serious deformation failures have occurred during construction of a main shaft. A study of construction parameters of the main shaft is required. First, the stability of the shaft and wall-rock is investigated by numerical methods. The modeling results are as follows： The convergence of shaft liner is greater than 60 mm at a depth of 650 m; the maximum principal stress in the liner approaches 190 MPa, which exceeds the strength of the liner, so it is inevitable that the liner deform locally. Second, stability analysis of shafts with different liner thicknesses has been completed. The results have the following features： If the depth where the liner thickness is increases from 400 mm to 500 mm is 650 meters, the convergence deformation of the liner is reduced by 3.4 mm while the maximum principal stress is reduced by 5 MPa. At a depth of 250 m if the liner thickness is increased from 400 mm to 500 mm the convergence of the liner is reduced by 1.5 mm while the maximum principal stress is reduced by 10 MPa. Therefore, increasing the liner thickness has little effect on liner convergence but can reduce the maximum principal stress in the liner. The thickness of the liner can be increased to reduce the maximum principal stress and increase the capacity for shear deformation. Finally, construction techniques employing releasing-displacements have been numerically simulated. The conclusions are that as the releasing displacement is increased the convergence of the surrounding rock increases linearly while the convergence of the lining decreases linearly. The plastic zone in the surrounding rock mass at first increases linearly but then, at a release-displacement of 95 ram, expands rapidly. These conclusions show that use of suitable releasing displacement can increase the self-supporting capacity of the surrounding rock. But when the releasing displacement exceeds 95 nun the plastic zone rapidly enlarges and stability rapidly decreases. The maximum principal st

摘要：Soft rock surrounding deep roadway has poor stability and long-term rheological effect. More and larger deformation problems of surrounding rock occur due to adverse supporting measures for such roadways, which not only affects the engineering safety critically but also improves the maintenance costs. This paper takes the main rail roadway with severely deformation in China＇s Zaoquan coal mine as an example to study the long-term deformation tendency and damage zone by means of in-situ deformation monitoring and acoustic wave testing technique. A three-dimensional finite element model reflecting the engineering geological condition and initial design scheme is established by ABAQUS. Then, on the basis of field monitoring deformation data, the surrounding rock geotechnical and theological parameters of the roadway are obtained by back analysis. A combined supporting technology with U-shaped steel support and anchor-grouting is proposed for the surrounding soft rock. The numerical simulation of the combined supporting technology and in-situ deformation monitoring results show that the soft rock surrounding the roadway has been held effectively.

摘要：目的:探讨作用于大跨度曲面屋盖非定常气动力的特性,为考虑非定常气动力影响的大跨度曲面屋盖抗风设计提供理论参考。创新点:1.采用强迫振动试验;2.采用大涡模拟(LES)流入脉动风的生成方法;3.研究大跨度曲面屋盖非定常气动力特性。方法:1.通过强迫振动风洞试验方法探讨风速、强迫振动振幅、屋盖的矢跨比和缩减频率对非定常气动力的影响;2.采用计算流体力学数值模拟重现风洞试验,从而在更宽的缩减频率范围内分析非定常气动力的特性,并且通过可视化流场的分析探讨风与屋盖相互作用的机理。结论:1.屋盖的振动对屋盖表面的风压分布影响较大。2.屋盖的振动可能抑制屋盖背风面漩涡的脱落。3.根据风洞试验和数值模拟的结果分析得到的矢跨比、风速和振动振幅对气动阻尼系数和气动刚度系数的影响较小;气动阻尼系数和气动刚度系数主要随着缩减频率的变化而变化。4.气动刚度系数为正值,使得结构的总刚度减小,从而减小结构的固有频率;气动阻尼系数为负值,使得结构总阻尼增加。5.风洞试验和LES模拟结果的一致性可以说明,LES是一个能够有效研究非定常气动力特性的数值模拟方法。

摘要：In engineering projects associated with rock mechanic science like open pit mines, assessment and slope stability of mine walls is one of the important performance in generate of these structures. Estimating and knowledge of stable slope angle is one of main parts that should be occurring to special attention in open pit mines studies phase. Considering the importance of economic costs in mining issues, the need for appropriate design slope angle that can cause an adverse minimize project costs and throws the other hand, the stability conditions in the safe walls of the mine life will provide essential and seems obvious. Therefore, in this study to determine the optimal slope angle of overall and bench of west wall of the Chadormalu ore iron mine, has been trying, first, done field studies on the discontinuity of western wall, engineering classification and geomechanical properties of rock masses of wall, then assess the amount of optimal slope angle using empirical method. Finally, in order to ensure stability and accuracy of the wall slope angle based on the obtained (empirical method) tries to analysis is amount of Factor of Safety (FOS), displacements and mean stress condition atwalls calculated from drilling use Phase2D powerful software.

摘要：The paper proposes a topology optimization method for 1D phononic structures to minimize the tangential component of particle velocity at the objective *** tangential derivative of the boundary integral equation(TDBIE)is employed for the evaluation of the objective function involves the tangential derivative *** topological derivative is derived through the adjoint method and the Neumann boundary condition of the adjoint field is obtained using the *** average topological derivative which is obtained by calculating the average value of the topological derivative in each layer of design domains,is employed for the updating of the level set *** implementations demonstrate the proposed method is effective for the design of the 1D phononic crystals with the objective function involving tangential derivative quantities.