摘要：Entransy has been applied and studied in a broad range of heat transfer optimizations recently. Current study proposes the entransy of evaporators to conduct the optimization of heat exchangers in heating, ventilation, air conditioning and refrigeration systems. A novel finless bare tube heat exchanger was studied using a validated heat exchanger modeling tool. The capacity based optimization and entransy dissipation based thermal resistance were used and compared. The applicability of using entransy dissipation based thermal resistance in this type of heat exchanger optimization has been discussed. It has been demonstrated that minimizing entransy dissipation and maximizing capacity are equivalent to optimizing evaporators with fixed flow rates and different when optimizing evaporators with variable flow rates and the deviation is negligible when heat exchanger capacity is small(~1 k W) and more obvious as heat exchanger capacity increases. Thus entransy dissipation based thermal resistance could be used as an alternative optimization index to capacity for evaporators with fixed flow rate and small capacity evaporators with variable flow rates and should be used individually with capacity as an optimization index for evaporators with large capacity and variable flow rates.

摘要：The paper is concerned with the fluid flow in the impeller side clearances of a centrifugal pump with volute *** flow conditions in these small axial gaps are of significant importance for a number of effects such as disk friction,leakage losses or hydraulic axial thrust to name but a *** the investigated single stage pump,the flow pattern in the volute turns out to be asymmetric even at design flow *** gain a detailed insight into the flow structure,numerical simulations of the complete pump including the impeller side clearances are ***,the hydraulic head and the radial pressure distributions in the impeller side clearances are measured and compared with the numerical *** configurations of the impeller,either with or without balancing holes,are ***,three different operating points,i.e.:design point,part load or overload conditions are *** addition,analytical calculations are accomplished to determine the pressure distri-butions in the impeller side *** accurate boundary conditions are available,the 1D flow models used in this paper can provide reasonable results for the radial static pressure distribution in the impeller side ***,a counter rotating wake region develops in the rear impeller side clearances in absence of balancing holes which severely affects the inflow and outflow conditions of the cavity in circumferential direction.

摘要：Through systematical experiment design, the physical blowing agent(PBA) mass loss of bio-based polyurethane rigid foam(PURF)in the foaming process was measured and calculated in this study, and different eco-friendly PBA mass losses were measured quantitatively for the first time. The core of the proposed method is to add water to replace the difference, and this method has a high fault tolerance rate for different foaming forms of foams. The method was proved to be stable and reliable through the standard deviations σ1and σ2for R1(ratio of the PBA mass loss to the material total mass except the PBA) and R2(ratio of the PBA mass loss to the PBA mass in the material total mass) in parallel experiments. It can be used to measure and calculate the actual PBA mass loss in the foaming process of both bio-based and petroleumbased PURF. The results show that the PBA mass loss in PURF with different PBA systems is controlled by its initial mass content of PBA in PU materials ω. The main way for PBA to dissipate into the air is evaporation/escape along the upper surface of foam. This study further reveals the mechanism of PBA mass loss: the evaporation/escape of PBA along the upper surface of foam is a typical diffusion behavior. Its spread power comes from the difference between the chemical potential of PBA in the interface layer and that in the outside air. For a certain PURF system, R1has approximately linear relationship with the initial mass content of PBA in PU materials ω, which can be expressed by the functional relationship R1= kω, where k is a variable related to PBA’s own attributes.

摘要：Multi-component mixture(MCM) is a complicated chemical system that contains a great deal of mixture rays with various mixture ratios, and each ray includes many mixtures with different concentration ***, in combined toxicity field, almost all studies on MCM focus on the mixtures designed by the equivalenteffect concentration ratio(EECR) procedure. However, the EECR mixtures cannot represent the whole mixture system because the EECR mixtures are located on one mixture ray in concentration space formed by multiple components. In our view, some optimal experimental design such as the uniform design(UD) should be used to effectively select many representative mixture rays from the MCM system,instead of single EECR ray. The uniform design ray(UDray) integrating UD idea with fixed-ratio ray design can systematically and comprehensively measure the combined toxicity changes in the MCM system. This review introduces the operation method, construction of uniform table and corresponding usable table, and some cases of application of the UD-ray to help readers easily use UD-ray in their MCM toxicity assessment.

摘要：Two new metal-organic frameworks（MOFs）,[Cu2（H_2O）_2（BCPIA）]（BUT-20）and（Me_2NH_2）[In（BCPIA）]（BUT-21）were designed and synthesized through the solvothermal reaction between a newly created desymmetric 4-connected ligand,5-（2,6-bis（4-carboxyphenyl）pyridin-4-yl）isophthalic acid（H_4BCPIA）and Cu（NO_3）2 2.5H_2O or In（NO_3）_3·5H_2O,respectively,and characterized by single-crystal and powder Xray diffraction,thermogravimetric analysis,infrared spectroscopy,and elemental *** two MOFs have three-dimensional structures,in which both the BCPIA 4 ligand and metal-containing entities,Cu_2（COO）_4（H_2O）_2 and In（COO）_4 act as 4-connected ***,different linkage configurations of the two metal-containing nodes,quadrilateral Cu_2_TD_2（COO）_4（H_2O）_2and tetrahedral In（COO）_4,lead to distinct structural networks of BUT-20 and 21,with Nbo and Unc topologies,respectively.

摘要：Due to the increasingly stringent standards, it is important to assess whether the proposed emission reduction will result in ambient concentrations that meet the standards. The Software for Model Attainment Test-Community Edition （SMAT-CE） is developed for demonstrating attainment of air quality standards of O3 and PM2.5. SMAT-CE improves computational efficiency and provides a number of advanced visualization and analytical functionalities on an integrated GIS platform. SMAT-CE incorporates historical measurements of air quality parameters and simulated air pollutant concentrations under a number of emission inventory scenarios to project the level of compliance to air quality standards in a targeted future year. An application case study of the software based on the U.S. National Ambient Air Quality Standards （NAAQS） shows that SMAT-CE is capable of demonstrating the air quality attainment of annual PM2.5 and 8-hour O3 for a proposed emission control policy.

摘要：High-steep slope stability and its optimal excavation design in Shuichang open pit iron mine were analyzed based on a large 3D physical simulation technique. An optimal excavation scheme with a relatively steeper slope angle was successfully implemented at the northwest wall between Nos. 4 and 5 exploration lines of Shuichang Iron Mine, taking into account the 3D scale effect. The phys-ico-mechanical properties of rock materials were obtained by laboratory tests conducted on sample cores from exploration drilling directly from the iron mine. A porous rock-like composite material was formed for the model, and the mechanical parameters of the material were assessed experimentally;specifically, the effect of water on the sample was quantitatively determined. We adopted an experimental setup using stiff modular applied static loading to carry out a visual excavation of the slope at a random depth. The setup was equipped with acous-tic emission （AE） sensors, and the experiments were monitored by crack optical acquirement, ground penetrating radar, and close-field pho-togrammetry to investigate the mechanisms of rock-mass destabilization in the high-steep slope. For the complex study area, the model re-sults indicated a clear correlation between the model＇s destabilization resulting from slope excavation and the collected monitoring informa-tion. During the model simulation, the overall angle of the slope increased by 1-6 degrees in different sections. Dramatically, the modeled excavation scheme saved over 80 million tons of rock from extraction, generating enormous economic and ecological benefits.

摘要：针对意大利歌剧院进行研究,着重研究建筑设计对厅堂音质的影响.对两个剧院的常规音质参量进行了测量.这两座剧院是由同一建筑师Antonio Galli Bibiena设计的,分别是波仑亚的市立剧院和曼图亚的科学剧院.二者具有相当近似的形式,但尺寸不同,所用的材料也各异,前者是用砖石建成,后者是用木料建成,因此在整修前采用了许多预应力钢筋混凝土结构.文中提供了不少数据并给出了对这些数据加以比较和分析的结果,特别是关于某些特征尺寸与扫频信号各可闻频率产生的空间听觉感受之间相关性的分析,以及若干有关材料和体型对IACC和EDT等音质参量的影响的思考.

摘要：Efficient catalysts enable MgH2 with superior hydrogen storage ***,we successfully synthesized a catalyst composed of Ce and Ni (***_(5) alloy) with splendid catalytic action for boosting the hydrogen storage property of magnesium hydride (MgH_(2))The MgH2–5wt%CeNi_(5) composite’s initial hydrogen release temperature was reduced to 174℃ and approximately 6.4wt%H_(2) was released at 275℃ within 10 ***,the dehydrogenation enthalpy of MgH_(2) was slightly decreased by adding CeNi_(5).For hydrogenation,the fully dehydrogenated sample absorbed 4.8wt%H_(2) at a low temperature of 175℃.The hydrogenation apparent activation energy was decreased from(73.60±1.79) to (46.12±7.33) kJ/*** analysis revealed that Mg_(2)Ni/Mg_(2)NiH_(4) and CeH_(2.73) were formed during the process of hydrogen absorption and desorption,exerted combined“Gateway”and“Spillover”effects to reduce the operating temperature and improve the hydrogen storage kinetics of MgH_(2).Our work provides an example of merging“Gateway”and“Spillover”effects in one catalyst and may shed light on designing novel highly-effective catalysts for MgH_(2) in near future.

摘要：This paper presents and tests three earthing systems (TT, TN and IT) for Micro-Grid (MG) protection against various fault types when the MG transferred to the islanding mode. The main contribution of this work is including the models of all micro sources which interfaced to the MG by power electronic inverters. Inverters in turns are provided with current limiters and this also included with the inverter models to exactly simulate the real situation in the MG during fault times. Results proved that the most suitable earthing system for MG protection during the islanding mode is the TN earthing system. That system leads to a suitable amount of fault current sufficient to activate over current pro-tection relays. With using TN earthing system, touch voltages at the faulted bus and all other consumer’s buses are less than the safety limited values during islanding mode. For the two others earthing systems (TT and IT), fault currents are small and nearly equal to the over load currents which make over current protection relay can not differentiate between fault currents and overload currents. All models of micro sources, earthing systems, inverters and control schemes are built using Matlab?/Simulink? environment.