摘要：Aluminium alloy AA2219 is a high strength alloy belonging to 2000 series. It has been widely used for aerospace applications, especially for construction of cryogenic fuel tank. However, arc welding of AA2219 material is very critical. The major problems that arise in arc welding of AA2219 are the adverse development of residual stresses and the re-distribution as well as dissolution of copper rich phase in the weld *** effects increase with increase in heat input. Thus, special attention was taken to especially thick section welding of AA2219-T87 aluminium alloy. Hence, the present work describes the 25 mm-thick AA2219-T87 aluminium alloy plate butt welded by GTAW and GMAW processes using multi-pass welding procedure in double V groove design. The transverse shrinkage, conventional mechanical and metallurgical properties of both the locations on weld joints were studied. It is observed that the fair copper rich cellular(CRC) network is on Side-A of both the weldments. Further, it is noticed that, the severity of weld thermal cycle near to the fusion line of HAZ is reduced due to low heat input in GTAW process which results in non dissolution of copper rich phase. Based on the mechanical and metallurgical properties it is inferred that GTAW process is used to improve the aforementioned characteristics of weld joints in comparison to GMAW process.

摘要：With the aid of numerical method, both flow field and its accompanied loss mechanism within the rotating cavity are investigated in detail in the 1^(st) part of the two parts paper. For ease of comparison, rotating cavity is further classified as the rotor-stator cavity case and the rotor-rotor cavity case. Results indicate that flow within both kinds of the cavity act as the inviscid flow except that the flow near walls, neighboring the lower G region and in the vicinity of the rotating orifices. In the regions except such inviscid-flow-dominate domains, the theoretical core rotation factor can be safely used to predict the swirl ratio within the cavity. When detailed flow pattern is considered, Ekman-type flow exists near periphery of the surface's boundary layer where viscous effect is non-negligible. However, due to the complex profile of the simulated cavity case, vortices structure is varied within the cavity. By comparison, swirl ratio can be used to predict the magnitude of loss. Due to the relatively evident rotating effects of the rotor-rotor cavity, swirl ratio even increases to 1.4 in the current model, which means that flow is moving faster than the surrounding disc. Further investigation finds that this kind of highly rotating flow is accompanied with serious undesirable pressure loss. Parenthetically, unlike its counterpart, swirl ratio above 1.0 doesn't happen when fluid passes through the rotor-stator cavity. So it is suggested that rotor-rotor flow cavity with the superimposed inward throughflow should be avoided in the engine design or certain measurements should be provided when such structure design is unavoidable. Simulation done in the current paper is meaningful since these dimensional parameters are typical in the design of state-of-art. Relatively lower range of Re_φ and C_w is not considered in the current two parts paper.

摘要：According to the statistics of straight thread sucker rods' application in screw pump in Daqing Oilfield before 2000, the proportion of sucker rods' yearly breakaway reached to 41.6%, taking up 70% of the total wells that were checked. Thus it can be seen that the rods breakaway problem was becoming the main barrier restricting screw pump large-scale population and application. Since then, the development work on the special sucker rods for screw pump had been carried on. Through the analysis on the failure position and failure form of the sucker rods', the following conclusions

摘要：The present study reports investigations on rheological,mechanical,thermal,tribological and morphological properties of feedstock filaments prepared with polylactic acid-polyether ketone ketone-hydroxyapatite-chitosan(PLA-PEKK-HAp-CS)composite for 3D printing of functional *** study consists of a series of melt processing operations on melt flow index(MFI)setup as per ASTM D-1238 for melt flow certainty followed by fixation of reinforcement composition/proportion as 94%PEKK-4%HAp-2%CS(B)by mass in PLA matrix(A).The blending of reinforcement and preparation of feedstock filament for fused deposition modeling(FDM)set up has been performed on commercial twin screw extruder(TSE).The results of study suggest that feedstock filaments prepared with blend of 95%A-5%B(by mass)at 200℃processing temperature and 100 r/min rotational speed on TSE resulted into better tensile properties(35.9 MPa peak strength and 32.3 MPa break strength)with 6.24%surface porosity,42.67 nm surface roughness(R_(a))and acceptable heat capacity(2.14 J/g).However as regards to tribological behavior,the minimum wear of 316μm was observed for sample with poor tensile *** regards to crash application for scaffolds the maximum toughness of 1.16 MPa was observed for 85%A-15%B(by mass)at 200℃processing temperature and 150 r/min rotational speed on TSE.

摘要：In 3D models retrieval, feature description and retrieval of non-rigid model face more complex problems due to the isometry transformation of itself. We introduce the hierarchical combination matching into the feature comparison, and build a map between the divided regions of two models, and then achieve accurate feature matching based on patch-by-patch, which successfully introduces the spatial information into feature matching. Verified by experiment, the 3D model retrieval method proposed in this paper based on hierarchical combination matching can make sure more accurate feature matching, so as to enhance the precision of retrieval.

摘要：For seismic design of structure and machinery, it is important to reproduce input earthquake motions that are likely to occur at a target site. Among the various methods used for generating artificial earthquake motions, the Synthesis Method of Trigonometric Function is used widely. In this method, artificial waves are reproduced by superimposing sine waves and then adding information about amplitude and phase in the frequency domain. In the Japanese architectural design code, the amplitude is standardized as the target response spectrum, and the phase can be defined by random numbers or by the phase of one observed wave. However, a random phase is distinctly different from the phase of an actual earthquake. Further, the phase of one observed wave is confined to the phase characteristic of the artificial wave of only one specific earthquake motion. In this paper, the authors introduce a new convenient method to reproduce artificial waves that not only satisfy the standardized spectrum property but also have the time-frequency characteristics of multiple observed waves. The authors show the feature of the artificial waves, discuss the merits of the method by comparing with existing methods, and report the tendencies of the non-liuear response by using simple model.