摘要：The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power *** this work,the traditional thermo-mechanical treatment was modified via the replacement of hot-rolling with cold rolling,i.e.,normalizing,cold rolling,and tempering (NCT),which was developed to improve the creep strength of the FGHAZ in G115 steel *** NCT treatment effectively promoted the dissolution of preformed M_(23)C_(6)particles and relieved the boundary segregation of C and Cr during welding thermal cycling,which accelerated the dispersed reprecipitation of M_(23)C_(6) particles within the fresh reaustenitized grains during post-weld heat *** addition,the precipitation of Cu-rich phases and MX particles was promoted evidently due to the deformation-induced *** a result,the interacting actions between precipitates,dislocations,and boundaries during creep were reinforced *** this strategy,the creep rupture life of the FGHAZ in G115 steel weldments can be prolonged by 18.6%,which can further push the application of G115 steel in USC power plants.

摘要：Al Si10Mg porous protective structure often produces different damage forms under compressive loading,and these damage modes affect its protective *** order to well meet the service requirements,there is an urgent need to comprehensively understand the mechanical behavior and response mechanism of AlSi10Mg porous structures under compressive *** this paper,Al Si10Mg porous structures with three kinds of volume fractions are designed and optimized to meet the requirements of high-impact,strong-energy absorption,and lightweight *** mechanical behaviors of AlSi10Mg porous structures,including the stress-strain relationship,structural bearing state,deformation and damage modes,and energy absorption characteristics,were obtained through experimental studies at different loading *** damage pattern of the damage section indicates that AlSi10Mg porous structures have both ductile and brittle mechanical *** simulation studies show that the AlSi10Mg porous structure undergoes shear damage due to relative misalignment along the diagonal cross-section,and the damage location is almost at 45°to the load direction,which is the most direct cause of its structural damage,revealing the damage mechanism of AlSi10Mg porous structures under the compressive *** normalized energy absorption model constructed in the paper well interprets the energy absorption state of Al Si10Mg porous structures and gives the sensitive location of the structures,and the results of this paper provide important references for peers in structural design and optimization.

摘要：Cortical electrodes are a powerful tool for the stimulation and/or recording of electrical activity in the nervous ***,the inevitable wound caused by surgical implantation of electrodes presents bacterial infection and inflammatory reaction risks associated with foreign body ***,inflammation of the wound area can dramatically worsen in response to bacterial *** consequences can not only lead to the failure of cortical electrode implantation but also threaten the lives of ***,we prepared a hydrogel made of bacterial cellulose(BC),a flexible substrate for cortical electrodes,and further loaded antibiotic tetracycline(TC)and the anti-inflammatory drug dexamethasone(DEX)onto *** encapsulated drugs can be released from the BC hydrogel and effectively inhibit the growth of Gram-negative and Gram-positive ***,therapeutic cortical electrodes were developed by integrating the drug-loaded BC hydrogel and nine-channel serpentine arrays;these were used to record electrocorticography(ECoG)signals in a rat *** to the controlled release of TC and DEX from the BC hydrogel substrate,therapeutic cortical electrodes can alleviate or prevent symptoms associated with the bacterial infection and inflammation of brain *** approach facilitates the development of drug delivery electrodes for resolving complications caused by implantable electrodes.

摘要：Three-dimensional(3D)printing has attracted increasing research interest as an emerging manufacturing technology for devel-oping sophisticated and exquisite architecture through hierarchical *** has also been employed in various advanced industrial *** development of intelligent biomedical engineering has raised the requirements for 3D printing,such as flexible manufacturing processes and technologies,biocompatible constituents,and alternative ***,state-of-the-art 3D printing mainly involves inorganics or polymers and generally focuses on traditional industrial fields,thus severely limiting applications demanding biocompatibility and *** this regard,peptide architectonics,which are self-assembled by programmed amino acid sequences that can be flexibly functionalized,have shown promising potential as bioinspired inks for 3D ***,the combination of 3D printing and peptide self-assembly poten-tially opens up an alternative avenue of 3D bioprinting for diverse advanced ***,a small but innovative nation,has significantly contributed to 3D bioprinting in terms of scientific studies,marketization,and peptide architectonics,including modulations and applications,and ranks as a leading area in the 3D bioprinting *** review summarizes the recent progress in 3D bioprinting in Israel,focusing on scientific studies on printable components,soft devices,and tissue *** paper further delves into the manufacture of industrial products,such as artificial meats and bioinspired supramolecular architectures,and the mechanisms,physicochemical properties,and applications of peptide ***,Israel contributes significantly to the field of 3D bioprinting and should thus be appropriately recognized.

摘要：聚合物基固态电解质得益于其易加工性,最有希望应用于下一代固态锂金属电池.目前,聚合物基态电解质的离子电导率提升策略多为加入导锂陶瓷以构建离子传输通道,其提升程度有限.电场在锂离子输运过程中存在重要影响,目前研究中有关电场对锂离子传输的影响机制尚不明确.本文将兼具高离子电导率和高介电常数的铌酸锂嵌入聚偏氟乙烯基体中,设计了一种新型复合固态电解质.铌酸锂颗粒有效调节电解质内部电场结构,增强了离子输运方向电场强度,实现了离子电导率的大幅提升(7.39×10^(-4)S cm^(-1),25℃).该电解质匹配高镍正极和锂金属负极的固态电池可稳定循环1000次以上,容量保持率为72%.该研究为设计下一代固态锂电池用高离子电导复合固态电解质提供了新的策略.

摘要：具有随机孔隙的多孔泡沫在声音管理应用中得到越来越多的利用,其吸声系数通常作为性能评估和设计优化的关键声学参数.根据不同的加工方法,泡沫中的孔隙可以是全开或半开的,并且通常表现为分形分布特征.为了便于工程应用,有必要对这些泡沫的吸声系数进行分析预测.然而,分析预测泡沫的吸声系数是一个挑战.因此,本研究提出了半开孔和全开孔的简化代表结构来微观分析泡沫内部的流动特性,并应用分形理论来描述随机分布的孔隙.引入一个叫“开孔度”的参数来表征孔隙的开放程度,可以解析地获得代表结构的粘性和热特征长度.随后,在经典吸声系数Johnson-Champoux-Allard模型的基础上,建立了一种将代表结构与分形理论统一起来的解析模型,从而可以将吸声系数作为具有全开/半开孔泡沫的关键形态参数的函数进行预测.与已有的实验测量和数值模拟结果相比,本文提出的分析模型可以较好地预测了半开孔和全开孔泡沫的关键流动特性和吸声系数.在0到4500 Hz的频率范围内,半开孔泡沫相对于具有相同孔隙率的全开孔泡沫可以更好地衰减声波.在孔隙率为0.95的条件下,半开孔泡沫的总体吸声系数分别提高了21.2%、57.7%和75.8%,此时开孔度由0.75到0.50降低了0.25.

摘要：The alloying behavior and microstructures of the(CoCrFeNiMn)_(90)M_(10)(M=Al,Hf)high-entropy alloy(HEA)powders fabricated by mechanical alloying were *** CoCrFeNiMn)_(90)Al_(10) powders have duplex solid-solution *** contrast,nanocrystalline HfNi_(3) anchoring in amorphous structures is found in the(CoCrFeNiMn)_(90)Hf_(10) ***(CoCrFeNiMn)_(90)Al_(10) powders show better ferromagnetic behaviors,mainly explained by the facilitated motion of the magnetic domain induced by the coherent interface between duplex *** with our previous work,the rules of forming solid-solution and amorphous phase in as-milled HEA powders are preliminarily *** is found that,compared with the as-cast HEA reported previously,the variation range of mixing enthalpy with atomic size difference of the solid-solution formed in as-milled HEA powders is ***,the variation ranges between mixing enthalpy and entropy with atomic size difference of the amorphous phase in HEA powder become wider than those of high-entropy bulk metallic glass.

摘要：In this study,a high impact resistant multi-layered composite consisting of continuous carbon fibre/nylon(CCF)and short carbon fibre/nylon(SCF)layers is developed via 3D printing *** effect of CCF/SCF layers configuration on the impact resistance is investigated by low-velocity impact test,and the impact failure mechanism of the 3D printed composites is explored by microscopic observations and finite element(FE)simulation *** results show that the 3D printed multi-layered composite with SCF layers distributed in the middle(HFA)exhibits higher impact resistant performance than the specimens with alternating SCF/CCF layers(HFB)and CCF layers distributed in the middle(HFC).The effect of CCF/SCF layers proportion on the impact performance is also studied by FE simulation,and the results show that the specimen with a CCF/SCF proportion of 7.0 exhibits the highest impact strength.

摘要：Designing strong, yet ductile, and body-centered cubic(BCC) medium-entropy alloys(MEAs) remains to be a challenge *** this study, the strength–ductility trade-off of Ni_(0.6)CoFe_(1.4)MEAs was tackled via introducing a BCC + face-centered cubic(FCC) dual-phase microstructure. Ni_(0.6)CoFe_(1.4)Nbx(x = 0, 0.05, 0.08, 0.10, and 0.15, in molar ratio) MEAs were prepared using vacuum induction melting. Results show that the new alloy is composed of BCC plus FCC dual phases featuring a network-like structure, and the BCC phase is the main phase in this alloy system. Moreover, the Nb0.10 MEA shows high strength and respectable tensile ductility, representing the best combination of the strength and fracture elongation among the alloys studied here. The remarkable strength of the Nb0.10 MEA is attributed to the combined effect of the solid solution strengthening, the precipitation hardening effect and the interface strengthening effect.

摘要：Corrosion,more specifically,pitting corrosion happening extremely in marine environments,leads to lifespan of materials drastically decreasing in service,which causes enormous economic loss and even environmental disaster and *** the past decade,increasing efforts have been made to study the corrosion behaviors of materials in chloride-containing aqueous ***,this work provides an overview of recent progress in understanding the degradation mechanism and improving the corrosion resistance and corrosion-wear resistance of materials from bulk metal to surface treatment involving organic coating,metal and its alloy or compound *** particular emphasis is given to the periodic layered structures(PLSs),whose anti-corrosion properties outperformed others to some extent,wherever in terms of bulk metal or surface treatment,regardless of aggressive environment(corrosion or corrosion-wear conditions).Numerical simulation based on kinds of models at different scales is introduced to deeply understand the process of corrosion and/or corrosion-wear in chloride-containing aqueous *** experimental result with numerical simulation,the micro-galvanic corrosion dominated degradation mechanism of PLSs is critically *** of setups to realize corrosion-wear in laboratory are also *** last,future research and development are prospected,offering to develop a basic application of PLSs designed by corrosion protection methodology in the near future.